Product ID:960Y001 EPOXY PRIMER MIL-P-23377D COMPONENT A
MSDS Date:04/01/1983
FSC:8010
NIIN:00-142-9279
Kit Part:Y
MSDS Number: BBJPQ

ENTERPRISE CHEMICAL COATINGS CO-DIV INSILCO CORP

2841 S ASHLAND AVE
CHICAGO, IL 60608-5322
US

Emergency Phone: 312-541-9000

Info Phone: 312-541-9000

Cage: 60035

ENTERPRISE CHEMICAL COATING CO DIV OF INSILCO CORP

CHICAGO, IL 60608-5322 US

Cage: 60035

STRONTIUM CHROMATE (SUSPECTED HUMAN CARCINOGEN BY ACGIH,

CAS: 7789-06-2

RTECS: GB3240000

Fraction By Weight: 20.3%

OSHA PEL 100 UG/CUM

ACGIH TLV: 0.001 MG/CUM IC

EPA Report Quantity: 10 LBS

DOT Report Quantity: 10 LBS

TOLUENE (IARC CARC- GROUP 3) *97-2*

CAS: 108-88-3

RTECS: XS5250000

Fraction By Weight: 5.3%

OSHA PEL 100 PPM

ACGIH TLV: 100 PPM

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

BUTYL ACETATE (N-BUTYL ACETATE) *97-2*

CAS: 123-86-4

RTECS: AF7350000

Fraction By Weight: 12.3%

OSHA PEL 710 MG/CUM

ACGIH TLV: 713 MG/CUM

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

CELLOSOLVE ACETATE (ETHYLENE GLYCOL ETHYL ETHER ACETATE),

CAS: 111-15-9

RTECS: KK8225000

Fraction By Weight: 3%.%

OSHA PEL 100 PPM

ACGIH TLV: 5 PPM SKIN

METHYL ETHYL KETONE, 2-BUTANONE *97-2*

CAS: 78-93-3

RTECS: EL6475000

Fraction By Weight: 3.8%

OSHA PEL 200 PPM

ACGIH TLV: 590 MG/CUM

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

PROPYL ALCOHOL, N-PROPANOL *96-4*

CAS: 71-23-8

RTECS: UH8225000

Fraction By Weight: 5.8%

OSHA PEL 500 MG/CUM

ACGIH TLV: 492 MG/CUM

ISOPARAFFINIC HYDROCARBONS (NAPHTHA PETROLEUM),

CAS: 64742-48-9

Fraction By Weight: 8.3%

PROPYLENE GLYCOL METHYL ETHER (1-METHOXY-2-PROPANOL)

CAS: 107-98-2

RTECS: UB7700000

Fraction By Weight: 2.2%

ACGIH TLV: 100 PPM

Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Health Hazards Acute and Chronic:INHALATION: CHROMIUM: ANESTHETIC
EFFECTS. IRRITATION OF RESPIRATORY TRACT/NERVOUS SYSTEM DEPRESSION.
SKIN/EYES: PRIMARY IRRITATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:IRRITATION, HEADACHE, DIZZINESS,
UNCONSCIOUSNESS, COMA.

First Aid:INHALATION: REMOVE FROM EXPOSURE. RESTORE BREATHING. KEEP
WARM & QUIET. EYES: FLUSH IMMEDIATELY W/WATER. SKIN: WASH W/WATER.
OBTAIN MEDICAL ATTENTION IN ALL CASES.

Flash Point:40F
Lower Limits:1.1
Extinguishing Media:ANY CLASS B FIRE EXTINGUISHER.
Fire Fighting Procedures:USE FULL PROTECTIVE EQUIPMENT W/SCBA. WATER
SPRAY MAY BE INEFFECTIVE. IF WATER SPRAY IS USED, FOG NOZZLES ARE
PREFERRED. WATER MAY BE USED TO COOL CONTAINERS.
Unusual Fire/Explosion Hazard:KEEP CONTAINERS TIGHTLY CLOSED. MAY
EXPLODE WHEN EXPOSED TO EXTREME HEAT. ISOLATE FROM HEAT/IGNITION
SOURCES. APPLICATION TO HOT SURFACES REQUIRES PRECAUTIONS.

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION. AVOID VAPORS.
VENTILATE AREA. CONTAIN & REMOVE W/INERT ABSORBENT & NONSPARKING
TOOLS.

Handling and Storage Precautions:STORE LARGE QUANTITIES IN BUILDINGS
DESIGNED AND PROTECTED FOR STORAGE COMPLIANCE WITH OSHA.
Other Precautions:EMPTY DRUM MAY CONTAIN HAZARDOUS RESIDUE. KEEP AWAY
FROM HEAT, SPARKS & FLAME. DON'T CUT, PUNCTURE/WELD ON/NEAR
CONTAINER.

Respiratory Protection:MECHANICAL FILTER RESPIRATOR TO REMOVE SOLID
AIRBORNE PARTICLES OF OVERSPRAY DURING SPRAY APPLICATION.
Ventilation:GENERAL DILUTION/LOCAL EXHAUST TO KEEP CONCENTRATION BELOW
TLV & LEL BELOW STATED LIMIT.
Protective Gloves:NOT REQUIRED
Eye Protection:SAFETY EYEWEAR W/SPLASHGUARDS/SIDESHIELD
Other Protective Equipment:NOT NORMALLY REQUIRED.
Work Hygienic Practices:REMOVE/LAUNDER CONTAMINATED CLOTHING BEFORE
REUSE.
Supplemental Safety and Health
CONTAINS CHROMATE PIGMENTS. DURING SPRAY APPLICATION/DRIED FILM
SANDING, ENGINEERING & ADMINISTRATIVE CONTROLS MUST BE INSTALLED TO
MAINTAIN AN EXPOSURE LEVEL BELOW 0.1/MG/CUM AS CHROMIUM; OTHERWISE
T HE USE OF RESPIRATOR IS RECOMMENDED.

Boiling Pt:B.P. Text:174-313F
Vapor Density:>1
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:64.3

Stability Indicator/Materials to Avoid:YES
GREASE, WATER.
Stability Condition to Avoid:HEAT, ELECTRICAL EQUIPMENT, SPARKS, OPEN
FLAME, HOT SURFACES & OTHER IGNITION SOURCES.
Hazardous Decomposition Products:FROM BURNING: CO
Conditions to Avoid Polymerization:ELEVATED TEMPERATURES.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/LOCAL, STATE &
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.